Днес преодолях мързела си и инсталнах на другото компи едно Ubuntu.
Пробвах един запис с Brasero и всичко се получи ОК...записва си нормално със SATA записвачка...
=====================================
При ядрата 2.6 модула ide_scsi вече не е вече необходим затова при по-горните команди той липсва.
Например ето какво вади cdrecord dev=help
z@z-desktop:~$ cdrecord dev=help
Cdrecord-ProDVD-ProBD-Clone 2.01.01a65 (i686-pc-linux-gnu) Copyright (C) 1995-2009 J�rg Schilling
Supported SCSI transports for this platform:
Transport name: sg
Transport descr.: Generic transport independent SCSI
Transp. layer ind.:
Target specifier: bus,target,lun
Target example: 1,2,0
SCSI Bus scanning: supported
Open via UNIX device: not supported
Transport name: pg
Transport descr.: SCSI transport for ATAPI over Parallel Port
Transp. layer ind.:
Target specifier: bus,target,lun
Target example: 1,2,0
SCSI Bus scanning: supported
Open via UNIX device: not supported
Transport name: ATA
Transport descr.: ATA Packet specific SCSI transport
Transp. layer ind.: ATAPI:
Target specifier: bus,target,lun
Target example: ATAPI:1,2,0
SCSI Bus scanning: supported
Open via UNIX device: not supported
Transport name: ATA
Transport descr.: ATA Packet specific SCSI transport using sg interface
Transp. layer ind.: ATA:
Target specifier: bus,target,lun
Target example: 1,2,0
SCSI Bus scanning: supported
Open via UNIX device: not supported
Transport name: RSCSI
Transport descr.: Remote SCSI
Transp. layer ind.: REMOTE:
Target specifier: rscsi@host:bus,target,lun
Target example: REMOTE:rscsi@host:1,2,0
SCSI Bus scanning: supported
Open via UNIX device: not supported |
........................................
........................................................
Пробвах също да запиша ISO през конзола със Cdrecord-ProDVD-ProBD-Clone 2.01.01a65 ....след като деинсталирах всички други записващи програми...
root@z-desktop:/home/z# cdrecord version
cdrecord: No write mode specified.
cdrecord: Assuming -sao mode.
cdrecord: If your drive does not accept -sao, try -tao.
cdrecord: Future versions of cdrecord may have different drive dependent defaults.
Cdrecord-ProDVD-ProBD-Clone 2.01.01a65 (i686-pc-linux-gnu) Copyright (C) 1995-2009 J�rg Schilling
Linux sg driver version: 3.5.34
Using libscg version 'schily-0.9'.
No target specified, trying to find one...
Using dev=1,0,0.
Device type : Removable CD-ROM
Version : 5
Response Format: 2
Capabilities :
Vendor_info : 'ASUS '
Identifikation : 'DRW-20B1ST '
Revision : '1.01'
Device seems to be: Generic mmc2 DVD-R/DVD-RW/DVD-RAM.
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-3 SWABAUDIO BURNFREE FORCESPEED
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R LAYER_JUMP
cdrecord: Warning: The DMA speed test has been skipped.
cdrecord: No such file or directory. Cannot open 'version'.
root@z-desktop:/home/z#
|
....................................................
..........................................................
Отново неуспешен запис:
z@z-desktop:~$ su
Password:
root@z-desktop:/home/z# cdrecord -v -eject speed=48 dev=1,0,0 Плот/arklinux-2008.1.iso
|
isocdrecord: No write mode specified.
cdrecord: Assuming -sao mode.
cdrecord: If your drive does not accept -sao, try -tao.
cdrecord: Future versions of cdrecord may have different drive dependent defaults.
Cdrecord-ProDVD-ProBD-Clone 2.01.01a65 (i686-pc-linux-gnu) Copyright (C) 1995-2009 J�rg Schilling
TOC Type: 1 = CD-ROM
scsidev: '1,0,0'
scsibus: 1 target: 0 lun: 0
Linux sg driver version: 3.5.34
Using libscg version 'schily-0.9'.
SCSI buffer size: 64512
atapi: 1
Device type : Removable CD-ROM
Version : 5
Response Format: 2
Capabilities :
Vendor_info : 'ASUS '
Identifikation : 'DRW-20B1ST '
Revision : '1.01'
Device seems to be: Generic mmc2 DVD-R/DVD-RW/DVD-RAM.
Current: CD-R
Profile: DVD+R/DL
Profile: DVD+R
Profile: DVD+RW
Profile: DVD-R/DL layer jump recording
Profile: DVD-R/DL sequential recording
Profile: DVD-RW sequential recording
Profile: DVD-RW restricted overwrite
Profile: DVD-RAM
Profile: DVD-R sequential recording
Profile: DVD-ROM
Profile: CD-RW
Profile: CD-R (current)
Profile: CD-ROM
Profile: Removable Disk
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-3 SWABAUDIO BURNFREE FORCESPEED
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
Drive buf size : 1867008 = 1823 KB
cdrecord: Warning: The DMA speed test has been skipped.
FIFO size : 4194304 = 4096 KB
Track 01: data 693 MB
Total size: 796 MB (78:57.49) = 355312 sectors
Lout start: 797 MB (78:59/37) = 355312 sectors
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 7
Disk Is not unrestricted
Disk Is not erasable
ATIP start of lead in: -11597 (97:27/28)
ATIP start of lead out: 359849 (79:59/74)
Disk type: Short strategy type (Phthalocyanine or similar)
Manuf. index: 20
Manufacturer: Princo Corporation
Capacity Blklen/Sparesz. Format-type Type
16763814 2048 0x00 No Media Present or Unknown Capacity
Blocks total: 359849 Blocks current: 359849 Blocks remaining: 4537
Forcespeed is OFF.
Starting to write CD/DVD/BD at speed 48 in real SAO mode for single session.
Last chance to quit, starting real write 0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
BURN-Free is OFF.
Performing OPC...
Sending CUE sheet...
cdrecord: CUE sheet not accepted. Retrying with minimum pregapsize = 1.
cdrecord: WARNING: Drive returns wrong startsec (0) using -150
Writing pregap for track 1 at -150
cdrecord: Input/output error. write_g1: scsi sendcmd: no error
CDB: 2A 00 FF FF FF 89 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 72 0B 00 00 00 00 00 0E 09 0C 00 00 00 02 00 00
Sense Key: 0x0 No Additional Sense, Segment 11
Sense Code: 0x00 Qual 0x02 (end-of-partition/medium detected) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 210.202s timeout 200s
write track pad data: error after 63488 bytes
BFree: 1652 K BSize: 1823 K
Starting new track at sector: 0
Track 01: 0 of 693 MB written.cdrecord: faio_wait_on_buffer for writer timed out.
cdrecord: Input/output error. write_g1: scsi sendcmd: no error
CDB: 2A 00 00 00 00 00 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 72 0B 00 00 00 00 00 0E 09 0C 00 00 00 02 00 00
Sense Key: 0x0 No Additional Sense, Segment 11
Sense Code: 0x00 Qual 0x02 (end-of-partition/medium detected) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 211.109s timeout 200s
write track data: error after 0 bytes
cdrecord: A write error occured.
cdrecord: Please properly read the error message above.
Writing time: 445.064s
Average write speed 10.8x.
Fixating...
Fixating time: 0.010s
cdrecord: fifo had 64 puts and 1 gets.
cdrecord: fifo was 0 times empty and 0 times full, min fill was 100%.
root@z-desktop:/home/z#
=============================================================
Закачам и лог от програмката HardInfo
Лога е от компютъра, на който не мога да записвам...
hardinfo_report.html
.............................................
Това от лога по-горе , не го разбирам точно:
Open via UNIX device: not supported
Отговор
За печат
Коментар